AW-Lake HM-F Flange Turbine Flow Meter

AW-Lake HM-F Flange Turbine Flow Meter can handle low viscosity fluids flowing under extremely high pressure. They are best suited for use with hydraulic oil, fuel and other light oils when ANSI or tri-clamp flanges are required. The turbine wheel’s low moment of inertia allows a fast acceleration from standstill up to full number of revolutions within 5 to 50 seconds, making dynamic measurements possible. This meter comes in twenty different flow ranges to meet your system requirements, from 0.008 to 12,000 gallons/minute.

Langed Turbine Flow Meter HM-F Series:

  • Fast Response Time & High Resolution: The Turbine wheel’s low moment of inertia allows a fast acceleration from standstill up to full number of revolutions within 5 to 50 sec. For that reason, dynamic measurements can be made. The resolution can amount to as much as 35,000 pulses per liter.
  • Wide Temperature Range: Standard turbine: -4 up to 248°F Special models for cryogenic liquids: -459°F Special models w/ hi-temp pickups: up to 662°F.
  • Low Contamination Risk :The spacing of the turbine wheel and bearing mount is wide enough to protect against particles in fluid jamming the turbine wheel. And the Twist of flow in this area has a self cleaning effect for the bearing.

AW-Lake HM-F Flange Turbine Flow Meter Features:

  • Measuring Accuracy: ±1.0% of reading or better
  • 20 Flow Ranges: 0.008 to 12,000 GPM
  • Pressure Rating: Depends on flange used
  • Temperature Rating: -384 to 662°F

Another Article:

AW-Lake HM-F Flange Turbine Flow Meter Specification:

  • Measuring Accuracy: ± 1.0% of reading or better
  • Repeatability: ± 0.05%
  • Flow Measuring Range:
    • .008 to .2 GPM
    • .08 to .4 GPM
    • .13 to 1.06 GPM
    • .2 to 2.6 GPM
    • .5 to 5 GPM
    • .9 to 9 GPM
    • 1.6 to 16 GPM
    • 2.2 to 22 GPM
    • 3.2 to 32 GPM
    • 4 to 40 GPM
    • 5.3 to 53 GPM
    • 6.6 to 66 GPM
    • 7.9 to 95 GPM
    • 9.2 to 106 GPM
    • 10.6 to 132 GPM
    • 13.2 to 198 GPM
    • 18.5 to 317 GPM
    • 26.4 to 528 GPM
    • 42.8 to 845 GPM
    • 66 to 1320 GPM
    • 79 to 1744 GPM
    • 94 to 2642 GPM
    • 114 to 3540 GPM
    • 219 to 6604 GPM
    • 423 to 12,680 GPM
  • Turn Down Ratio: 10:1
  • Maximum Operating Pressure: Working pressure is flange dependent
  • Maximum Operating Temperature: Fluid temperature of -384 to 662°F
  • Filtration Requirement: 300 microns
  • End Connection: Equipped with flanges as per DIN or ANSI
  • Materials Of Construction:
  • Body: 316 Ti Stainless Steel/ 316L
  • Rotor Support: 316 Ti Stainless Steel
  • Rotor: 429 Stainless Steel/329
  • Bearings: Tungsten Carbide with Nickel binder

Download Data Sheet: Langed Turbine Flow Meter HM-F Series

Ref: aw-lake.com

Share
%d bloggers like this: