Descriptions
Bamo BAMOPHAR 436 Turbidity Monitor is equipped with a color touch screen to set up the configuration and to display the turbidity, temperature and state of thresholds. Copies of measurement are available on 2 outputs 4-20 mA. BAMOPHAR 436 displays the turbidity value measured by one of our transmitters, to respond to process requirements.
- TURBICUBE in PVC or PPH and TRUBOMAT GAB in stainless steel, are dedicated to in-line measurement
- TURBISENS in PVC is an immersion probe with transmitter for measurements in tanks, basins, channels
Bamo BAMOPHAR 436 Features
- Color touch screen
- Available scales: 0.001 to 9999 FNU, FAU, NTU, mg/l, g/l
- 2 outputs 0/4-20mA (measurement & T.°C)
- 3 Independent relays
- 1 Relay for alarming function
- OPTIONS: RS 422 /J-BUS + LOGGER Extension terminal for a 2nd measurement parameter
A complete measuring system includes:
- One monitor BAMOPHAR 436
- One turbidity transmitter
OPTION: Extension terminal for a second parameter
- Allows a second measurement (pH, Flow rate, Conductivity, etc.) (Configuration and display on the main unit)
- Connected to main unit with 2 x 2-wire shielded cable (Cable length between both devices: max. 500 m)
- RS422 and Data Logger of main unit are shared between both units
- Wall or panel or DIN rail mounting: according to the model
Application
Turbidity measurement for monitoring and processing water treatment:
- Monitoring of source or wells for drinkable water
- Monitoring of filtering diaphragms, ultra-pure water production units, reverse osmosis plants
- Measurements in basins, decanting process
- Monitoring of clogging and rinsing of filtering units
- Monitoring of cooling towers
- Control of wastewater before discharge
Bamo BAMOPHAR 436 Specification
| End-user interface | Color touch screen 4.3”, resolution 480×272 pixels |
| Display of measurements, menus, temperature, relay status | |
| Configuration – Keyword protected | |
| Measuring scales | To set up according the turbidity transmitter in use (from 0.001 to 9999 FNU, FAU, NTU, mg/l, g/l) |
| Sensor signal input | For Turbidity transmitter 4-20 mA, 2-wire or 4-wire technique |
| Temperature display | Input signal for Pt 100 Ω 3-wire sensor, within the range 0 to 100 °C Or manually set up of operating temperature. |
| Relay outputs Configurable thresholds | 4 contacts N.O., potential free |
| Configurable thresholds | 2 Independent thresholds, for measurement or temperature |
| 1 Independent threshold, for measurement or temperature or to external function | |
| 1 threshold for alarming function (Temperature sensor fault) or measurement out of range | |
| Contact Initial resistance | 100 mΩ max. (voltage drop 6 V DC 1 A) |
| Switching power | 831VAAC/3A/277VAC |
| 90W/3A/30VDC | |
| Switching capacity (min.) | 100 mA, 5 V DC (variable according to switching frequency, environmental conditions and accuracy). |
| Measurement output | 0/4-20 mA (max. 600 Ω) proportional to measurement 0/4-20 mA (max. 600 Ω) |
| Temperature output | range 0 to 100 °C |
| Main power | 230 V – 50/60 Hz (others on request) – Consumption 10 VA |
| supply Models | Panel mounting, 96×144 mm; Front IP65; Rear IP4, screw terminals |
| Storage | Wall mounting, IP65, cable glands -10 … +70 °C |
| Operating temperature | -5 … +50 °C |
| Interface | RS422 output, J-BUS link – Binary slave mode – 2400 to 9600 bauds |
| Data Logger; Record of cycle average measurement – 150 000 records max. on memory |
Download Data Sheet: Turbidity Monitor BAMOPHAR 436
Reference: bamo.eu
Another Article:
- BAMOPHAR 451 Bamo Dissolved Oxygen Monitor
- BAMOPHAR 323 Bamo Conductivity / Resistivity
- BAMOPHAR 364 Bamo Conductivity Meter
- Bamo Flow Calculator for Open Channels BAMOPHAR 759