Level Controller SECURICUVE is float at the bottom of a stem moves a magnet inside the head housing. Fluid maintains the equipment (float, stem and magnet) in highest position ”a” (normal status).
Under thrust of fluid, float transmits level through a rod transmission to a vertical stem. Stem actuates a pointer on the dial, contacts&a potentiometer for output resistive signal image of level.
Electric gauge is mounted above tank&against liquid height, float transmits level through angle drive to vertical stem. Stem actuates on pointer associated with graduated dial to display level in tank
Magnetic Level Controller MNR 7 / 4074 has a magnetic equipment, a guiding stem with built-in Reed contact, fitting and head housing. Magnets are all covered by PTFE, non-porous quality.
Magnetic level controllers MNR 6 reed contacts are adjusted at factory according requested trigger points; They are actuated by the magnetic float. Wet parts are in PVC, PPH, PVDF or stainless steel.
Internal wiring is done on a screw terminal. On the lower end of guide tube, a blocking ring allows to take off the float before to fit the guide tube through a small diameter hole.
The Magnetic Level Controllers MNR 7 Reed contacts (up to 4) inside the stem, are actuated directly by the magnet float. Wet parts (stem and float) to choose between: or PVC & PP, or PP, or PVDF.
The Bamo’s model relay for resistive level detection ES 5000 works with the electrical conductivity property of the liquid, detecting the opening or closing circuit between two electrodes.
The Resistive Level Probes STS level probe with a relay ES 2001, detects a level of a conductive liquid. The current in detection loop provoques through the relay ES2001, an amplified ON/OFF signal.
EF 16 electrode is a single contact electrode. EFC 16 electrode is a dual-contact electrode, the outer body is used as the reference. No needs to provide a special ground connection.
Cable Suspended Resistive Level Probes HE / HS is the electrical resistance variation when the fluid touches the level electrode&reference electrode, causes an ON/OFF signal through the relay ES 2001.
Bamo is a company that comes from France. Electrical connection: with end tip to the terminal. A ground connection is available inside the housing IP55. Fitting is AISI 316 L with PTFE insulator(s).
The BES 680 resistive level detector, associated to a resistive relay, detects the variation of resistor value caused by the presence of a conductive liquid between two electrodes.
STE level probe in combination with a relay ES2001 detect level of electrically conductive liquids. Up to 5 levels may be triggered provide a reference electrode if tank is made of insulating material
RXM detects difference of resistance between detection electrode and the reference electrode when the liquid comes into contact. Reference can be the wall of the metal container or a second electrode.
Probes and electrodes are specially designed for different type of applications. ES2001 is used as a limit value detector on conductive liquids; Probes and rods are chosen according to the application
Level controller SNR 4, affords a dirt liquid as far as this one does not clog the measuring tube. Thresholds are adjustable. Pressure variation acts on a diaphragm that directly activates a contact.
The VAFLO regulates automatically, the high level of water, without power supply. The system is simply mechanical: When the level rises, the float causes the closure of the water inlet nozzle.
Level controller CNL, consists of float fixed to shaft which end has: magnet on metal models or magnetic float on PPH models. Float is moved by liquid&magnet acts on reed contact isolated from liquid.
Igema Multifunctional system LW designed with Low water limitation + discontinuous control (with EL913) or only discontinuous control (with EL912) for processes with limited construction supervision.
Operation of NIVOSTOP® / C is identical to other detectors NIVOSTOP® with a built-in counterweight. When the level is rising up, the tilting of the float actuates an integrated switch
The float switch with integrated counterweight is freely suspended down to the desired level. The float tilts upwards as the liquid level rises (see picture), then the built-in micro-switch commutes.
It is dual-channel units designed to evaluate the states of the conductive probe. They include a power supply 5V AC for supplying the probes and allows continuous sensitivity adjustment and time delay
The Eclipse® Model 706 High Performance Transmitter is a loop-powered, 24 VDC level transmitter that is based upon the proven and accepted technology of Guided Wave Radar (GWR).
The Enhanced Eclipse® Model 705 Transmitter is a looppowered. It is designed to provide measurement performance well beyond that of many traditional technologies, as well as “through-air” radar.
The ECLIPSE Model 700 supports both the FDT/DTM and Enhanced DD (EDDL) standards, which allow viewing of valuable configuration and diagnostic information such as the echo curve in tools.
Echotel ® Model 355 provides unsurpassed ease of configuration with either the menu-driven 4-push-button, 2-line ¥ 16-character display, HART® digital communications, or PACTware™.
Magnetrol offers an extensive range of innovative level controls. Echotel Model 335 is a high performance,non-contact ultrasonic transmitter for liquid level,volume,and open channel flow measurement.
Echotel ® Models 961 & 962 Ultrasonic Level Switches meet these demands with reliable transducer designs, extensive hazardous location approvals, and an advanced self-test technology.
Echotel Model 940 and 941 Ultrasonic Level Switches are compact integral units that utilize pulsed signal technology to perform high or low level measurement in a wide variety of liquid applications.
Magnetrol Echotel ® Model 910 Level Switches utilize ultrasonic contact technology for measuring level in clean liquid applications. The Echotel Model 910 is an integrally mounted system.
The Digital E3 Modulevel® is an advanced, intrinsically safe two-wire instrument utilizing simple buoyancy principle to detect and convert liquid level changes into a stable output signal.
Magnetic level indicators are precision engineered & manufactured to indicate liquid level accurately, reliably, & continuously. These units are completely sealed & require no periodic maintenance.
“Industry leader” is a role Magnetrol® has played for over 85 years. We manufactured the first liquid level switch to accurately and safely detect motion of liquid in boilers and feedwater systems.
Pulsar Process Measurement manufacture and supply a variety of level and volume measurement sensors, transducers and controllers to suit your application requirements including Ultrasonic Level.