LMag-F Litre Meter Electromagnetic Flanged Flow Meters

LMag-F Litre Meter Electromagnetic Flanged Flow Meters

Cost-effective flanged electromagnetic flow meter. The flanged LMag-F range of magflow meters represents great value for money, and meters are available for pipe sizes from 3” to 12” with ANSI pattern flanges. The electrodes are non-fouling, and LMag-F meters can be mounted with as little as 2x pipe diameter of upstream straight pipe run. Three styles are available depending on output and display position.

Specify meter-mounted or remote display for flexibility in positioning. Meters are CE certified and certified to NSF Standard 62 for Drinking Water Systems. LMag-F meters are IP68 rated and may be continuously submerged to 3m depth. Bidirectional flow reading is standard with totals available in forward, reverse, net flow, batch forward flow and batch reverse flow. Batch totals can be reset.

Pulse output is standard on all models and 4-20ma passive current loop is standard on the LMag-Fp. In addition, 4-20mA loop, HART protocol, high-speed digital and Modbus® are optional on externally powered units, depending on model. User-friendly backlit display & user interface Rate and total indication are standard. Rate and total units and pulse scaling can be set via the front panel touch key pad.

User-friendly backlit display & user interface

Rate and total indication are standard. Rate and total units and pulse scaling can be set via the front panel touch key pad.

  Another Article:

LMag-F magflow meters Features

Typical applications:

  • Water/wastewater treatment
  • Pump skids
  • Pumping stations
  • Packaged plants
  • Filtration systems
  • Reclaimed water
  • Easy setup
  • Minimal straight pipe
  • Mounted or remote rate & total
  • Tamper-evident seal
  • Certified to NSF/ANSI standard 61
  • IP68 rated
  • No moving parts

LMag-F magflow meters Specification

Pipe sizes: 3”, 4” 6”, 8” 10”, 12”
Flanges: 150 lb, ANSI pattern
Pressure: 10.3 bar
Temperatures: Operating -12º to 60º C
Storage -40º to 70º C
Accuracy: ±0.75% of reading, ±0.025% of full-scale flow from low flow cutoff to maximum flow rate of 10 m/sec
Low flow cutoff: 0.5% of maximum flow rate
Materials: Body Ductile cast iron, powder coated (3”), Welded steel, epoxy coated (4-12”)
Liner Noryl® (3”), Santoprene flange/polypropylene liner body (4-12”)
Electronics housing Powder-coated diecast aluminium
Electrodes 316 stainless steel
O-Ring EPDM
Power DC Power 9-36 Vdc @ 250 mA max, 30 mA average
Battery backup (not primary power) DC powered units: Two lithium 3.6V ‘D’ batteries, replaceable AC powered units: One 9V alkaline battery, replaceable
AC Power (remote and direct models) 85-264Vac, 50/60Hz, 0.12A
Battery (LMag-Fb only) One lithium 7.2V ‘D’ size battery pack, replaceable
Scaled pulse output: Signal Current sinking pulse, isolated, 36 Vdc at 10mA max
Pulse rates User-scalable from 0.1 to 99,999.9 volume units/pulse
Options 4-20mA current loop Isolated, passive, 24Vdc, 650 Ω maximum current loop
HART/4-20mA HART protocol over 4-20mA line
High speed digital output Isolated, open collector, 24Vdc (remote and direct only)
Serial communications Isolated, asynchronous serial RS485 (Reconfigurable for RS232 or 3.3V CMOS), Modbus® RTU protocol (factory selectable)
Cable: Power/Output cable 6m standard length polyurethane jacketed cable—for power and outputs (lengths up to 60m available)
Remote display cable 6m standard length polyurethane jacketed cable—for connection between meter and remote display (lengths up to 60m available)
Conductivity: >20 microSiemens/cm
Empty pipe detection: Hardware/software, conductivity-based
Regulatory (EN 61326), 4”-12” certified to NSF/ANSI standard 61 60°C; 3” certified to NSF/ANSI standard 61 Cold Water 23°C
Environmental NEMA 6P, IP68 (3m depth, continuously)

Download Datasheet: LMag-F Litre Meter Electromagnetic Flanged Flow Meters

Reference :litremeter.com

Share
%d bloggers like this: