MaxxFlow HTC Electromagnetic Flow MeasurementIndonesia Industrial Parts

Description

MaxxFlow HTC Electromagnetic Flowmeter is designed for measurement of high mass flow rates for dry bulk solids from the exit of pre feeding devices, e. g. screw conveyors, air slides, rotary valves, bucket elevators, etc.

Most non-metallic solids can be measured
Can be installed on round pipes or ducts
No real upper limit of mass flow
Maximum pressure 10 bar
Dust tight
No flow restrictions to the process flow (wear resistant ceramic liner)
The mass flow measurement is independent of flow characteristics
Can be installed at an angle
Small footprint, 220 mm (DN 100), 290 mm (DN 150), 310 mm (DN 200)
No moving parts, hence no maintenance
Easy to calibrate
Installation free of obstacles in the cross-section,therefore no dead spots
Independent of the arrangement of the line(vertical or inclined)
Easy retrofitting
Non-contact measurement procedure (no mechanics)
Maximum material temperature 120 °C
abrasion – resistant ceramic inner tube
maintenance-free
System accuracy: 0.04 %

MaxxFlow HTC System

A complete measuring point consists of these components:

Sensor for installation in the conveyor line
Evaluation Unit MSE 300
The sensor is available in sizes DN 70 mm, DN 100 mm, DN 150 mm and DN 200 mm.
With the design in DN 70 mm, the connection flange could be freely selected.
The evaluation unit, in Field housing or DinRail version, is connected to the sensor using 4-wired, shielded cable.
The maximum distance between sensor and evaluation unit is 300 m.

MaxxFlow HTC Specification

Sensor Electromagnetic

Housing material	Steel St 52, powder-coated (optional stainless steel 1.4571) NW 70/100/150/200 mm,
Housing material	Flange according EN 1092-1 / PN10 DN 70: variable
Inner pipe	Al₂O₃-Ceramic
Protection category	IP65, ATEX: Cat. 3D
Ambient temperature	Sensor pipe: – 20 … + 120 °C
Ambient temperature	Sensor electronic: 0 … + 60 °C
Max. working pressure	1 bar
Working frequency	88 kHz
Transmitting power	Max. 2 mW
Weight	Depend on diameter
Accuracy	± 1 … 3 % (based on end of measuring range and calibrated material)
System accuracy	± 0.04 %

MSE 300-DR (DIN Rail) Electromagnetic

Power supply	24 V DC ± 10 %
Power consumption	20 W / 24 VA
Protection type	IP40 to EN 60 529
Ambient operating temperature	-10 … +45 °C
Dimensions	23 x 90 x 118 mm (W x H x D)
Weight	Approx. 172 g
DIN rail fastening	DIN 60715 TH35
Connection terminals cable cross-section	0.2 – 2.5 mm² [AWG 24-14]
Current output	1 x 4 … 20 mA (0 … 20 mA).
Current output	load < 500
Interface	ModBus RTU (RS 485) / USB
Pulse output	Open Collector – max. 30 V, 20 mA
Relay contact	Max. rated load: 250 V AC
	Max. peak current: 6 A
	Max. rated load 230 V AC: 250 VA
	Max. breaking capacity DC1: 3/110/220 V: 3/0.35/0.2 A
	Min. switching load: 500 mW (10 V / 5 mA)

MSE 300-FH (Field Housing) Electromagnetic

Power supply	110 / 230 V AC 50 Hz (optional 24 V DC)
Power consumption	20 W / 24 VA
Protection type	IP65 to EN 60 52910.91
Ambient operating temperature	-10 … +45 °C
Dimensions	258 x 237 x 174 mm (W x H x D)
Weight	Approx. 2.5 kg
Interface	RS 485 (ModBus RTU) / USB
Cable screw connectors	3 x M20 (4.5 – 13 mm Ø)
Connection terminals cable cross-section	0.2 – 2.5 mm² [AWG 24-14]
Current output	3 x 4 … 20 mA (0 … 20 mA), load < 500 ? (Active)
Pulse output	Open Collector – max. 30 V, 20 mA
Relay contact	Max. rated load: 250 V AC
	Max. peak current: 6 A
	Max. rated load 230 V AC: 250 VA
	Max. breaking capacity DC1: 3/110/220 V: 3/0.35/0.2 A
	Min. switching load: 500 mW (10 V / 5 mA)
Data backup	Flash Memory