Description
Dwyer 2000-HA Magnehelic High Accuracy Magnehelic® Gage is twice as accurate as the standard Magnehelic® gage. The well-engineered High Accuracy Magnehelic® Gage offers a mirrored overlay as standard in order to eliminate any parallax error when taking measurements.
A six point calibration certificate is included with each high accuracy model. The rugged IP67 casing helps fully protect against dust and water ingress. The redesigned corrosion resistant brushed 304 stainless steel bezel option offers a clean tapered design, yet minimizes the possibility of any dust accumulation on the edges.
Dwyer 2000-HA Magnehelic Features
- Accurate within 1%
- Mirrored scale overlay eliminates parallax error
- Six point calibration certificate included
- IP67 – Fully protects against dust and immersion
- Optional corrosion resistant brushed 304 SS bezel
Application
- Clean room positive pressure indication
- Filter monitoring
- Air velocity with Dwyer pitot tube
- Blower vacuum monitoring
- Fan pressure indication
- Duct, room, or building pressures
Dwyer 2000-HA Magnehelic Specification
| Service | Air and non-combustible, compatible gases (natural gas option available). Note: May be used with hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi. |
| Wetted Materials | Consult Factory. |
| Housing | Die cast aluminum case and bezel with acrylic cover. Exterior finish is coated gray to withstand 168 hour salt spray corrosion test. |
| Accuracy | ±1% FS (±1.5% on -0, -100PA, -125PA, -10MM and ±2% on -00, -60PA, -6MM ranges) throughout range at 70°F (21.1°C). |
| Pressure Limits | -20 in Hg to 15 psig (-0.677 bar to 1.034 bar). |
| Overpressure | Relief plug opens at approximately 25 psig (1.72 bar), standard gages only. |
| Temperature Limits | 20 to 140°F (-6.67 to 60°C). |
| Size | 4″ (101.6 mm) diameter dial face. |
| Mounting Orientation | Diaphragm in vertical position. Consult factory for other position orientations. |
| Process Connections | 1/8″ female NPT duplicate high and low pressure taps – one pair side and one pair back. |
| Standard Accessories | Two 1/8″ NPT plugs for duplicate pressure taps, two 1/8″ pipe thread to rubber tubing adapters, and three flush mounting adapters with screws. |
| Weight | 1 lb 2 oz (510 g). |
| Agency Approvals | Meets the technical requirements of EU Directive 2011/65/EU (RoHS II). |
Download Data Sheet: Series 2000-HA High Accuracy Magnehelic® Differential Pressure Gage
Ref: dwyer-inst.com
Another Article:
- Dwyer Series 2000 Magnehelic Differential Pressure Gauges
- Dwyer Series VFLO Venturi Flow Meter with Magnehelic Gauge
- Dwyer Series 2000-SP Magnehelic Differential Pressure
- Dwyer Series AT22000 Magnehelic Differential Pressure
- Dwyer Pressure Accessories
- Dwyer Ultrasonic Flow Meter
- Delta Mobrey 131 Series Flow Switches
- Dwyer Series PFT Paddlewheel Flow Sensor
- Dwyer Series TDFS2 Thermal Dispersion Flow Switch
- Converter Flow Meter Alia AMC4000 Electromagnetic
- McCROMETER Differential Pressure Flow Meters
- McCROMETER ExactSteam™ V-Cone® Flowmeter
- Differential Pressure Transmitter D32 Series Delta Mobrey
- Differential Pressure Switch 381 Series Delta Mobrey
- VFT-510 Series Differential Pressure Transducer
- Dwyer PUB Series Portable Ultrasonic Flow Meter Kit
- Dwyer PUF Series Portable Ultrasonic Flow Meter Kit