Flocorp Tracer 1000 3G LTT1-3G 3rd Generation Radar Level MeterIndonesia Industrial Parts

Description

Flocorp Tracer 1000 3G LTT1-3G 3rd Generation Radar Level Transmitter is ideal for level measurement of liquids, solids, bulk materials, sludge, powders, and granules. With a maximum measuring distance of 60ft. the guided-wave technology sends the radar pulse down a probe to measure either liquids or solids.

The pulse hits the surface and is reflected up the probe to the sensor, where the transit time is translated into a distance using time of fight and time expansion. The amplitude of the reflection depends on the dielectric constant of the product. This technology is not affected by pressure, temperature, viscosity, vacuum, foam, dust, changes in dielectric constant, or coating of the probe.

Flocorp Tracer Level Meter

Features and Benefits

Interface level measurement
Up to (60ft. 8in) range
Very short minimum range (6in)
Simple Setup
Auto-calibration to any dielectric ? 1.5
Adjustable Sensitivity
Precise & Continuous accuracy
14-28VDC
Modbus
Protection class IP66, NEMA 4x
Measures extremely low dielectric (1.5)
Programmable fail-safe mode

Technology

The Tracer 1000™ uses TDR Technology: low-energy, high-frequency electromagnetic impulses, generated by the sensor’s circuitry, are propagated along with the probe which is submerged in the liquid or solid to be measured. When these impulses hit the surface of the media, part of the impulse energy is reflected up the probe to the circuitry which then calculates the level from the time difference between the impulses sent and the impulses reflected.

The sensor can output the analyzed level as a continuous measurement reading through its analog output. TDR Sensors are also known as Guided Radars or Guided Wave Radars.

Flocorp Tracer 1000 3G LTT1-3G Specification

ELECTRONICS
POWER	– 24VDC (14 to 28VDC)
POWER	– 2-Wire Loop
POWER CONSUMPTION	<500mW @ 24VDC
COMMUNICATIONS	– Modbus
	– HART
	– Tracer Software via Modbus or HART
ANALOG OUTPUT1	– 14V @ 0 Ohm
	– 19V @ 250 Ohms
	– 24V @ 500 Ohms
	– Current park at 4mA, 8mA, 12mA
MAXIMUM RANGE	– Flexible cable probe: 60ft 8in (18.5m)
MAXIMUM RANGE	– Rigid probe: 13ft 1in (4m)
MINIMUM RANGE (BLANKING)	150mm
DIELECTRIC RANGE	³ 1.5
FREQUENCY	2.2 GHz
RESOLUTION	– Analog: 1uA
RESOLUTION	– Display: 1.0mm
ACCURACY	+/- 3mm
MEASUREMENTS PER SECOND	3
RESPONSE TIME	<1 second (application dependant)
SUM OF NON-LINEARITY, NON- NON-REPEATABILITY, HYSTERESIS	Analog +/- 0.02%
REPEATABILITY	+/- 3mm
REPEATABILITY	Non-volatile (No backup battery required)
MEMORY	>10 years of data retention
OPERATING TEMPERATURE (ELECTRONICS)	-40ºF to +176ºF (-40ºC to +80ºC)
DISPLAY	4-line graphic display (128 x 64 pixels)
LANGUAGE	English
CONFIGURATION	4 button (up-down, Cal, Run), Tracer Software via HART
APPROVALS2	(USA) FM XP-AIS Cl. I Div 1, Grp A, B, C,
	D, T6…T2B, Cl. I Zone 0/1 AEx a/d [ia Ga] IIC T6…T2 Ga/ Gb
	(USA) FM DIP-AIS Cl. II/III Div 1, Grp E, F,
	G, T6…T2B, Zone 20/21 AEx ia/tb [ia Da]
	IIIC T85°C…T255°C Da/ Db
	(Canada) FM Cl. I Div 1, Grp A, B, C, D,
	T6…T2B
	(Canada) FM Cl. II/III Div 1, Grp E, F, G,
	T6…T2B
	(Canada) FM Cl. I Zone 0/1 Ex ia/d [ia Ga] IIC T6…T2 Ga/ Gb
	(Canada) FM Zone 20/21 Ex ia/tb [ia Da] IIIC T85°C…T255°C Da/ Db
	ATEX Ex II 1/2 G Ex ia/d [ia Ga] IIC T6… T2 Ga/Gb
	ATEX Ex II 1/2 D Ex ia tb [ia Da] IIIC T6… T2 Ga/Gb
	IECEx Ex ia/d [ia Ga] IIC T6…T2 Ga/Gb Tamb -40°C to 60°C
	IECEx Ex ia tb [ia Da] IIIC T85°C… T255°C Da Db Tamb -40°C to 60°C
	Safety Integrity Level rating SIL2 / SIL3
ENCLOSURE
TYPE	Dual Compartment with Glass window
MATERIAL	– Die-cast Copper-Free Aluminium, Epoxy Painted
MATERIAL	– 316L Stainless
CABLE ENTRIES	– 1/2” NPT
	– 3/4” NPT
	– M20 x 1.5
	– M25 x 1.5
IP RATING	– NEMA 4X
IP RATING	– IP66
PROBE
PROBE SIZE/ WETTED MATERIALS	4mm SS316L rod
	4mm DIN3055 (7×7 strand) SS316L flexible cable
	6mm SS316L rod
	6mm DIN3055 (7×7 strand) SS316L flexible cable
	8mm SS316L rod
	8mm DIN3055 (7×7 strand) SS316L flexible cable