General Information
Dinel Intrinsically Safe Supply Units are used for energizing of NAMUR output sensors (DLS–27Xi, CPS–24Xi, etc.) located in hazardous explosive areas. Due to the state of the connected sensor, they switch their output changeover relay contact or a transistor switch. Moreover, they can provide a simple 2-state level regulation (pump-up and pump-down control).
Dinel Intrinsically Safe Supply Units Features
- For energizing and state-detection of NAMUR sensors (EN 60947-5-6)
- The connected sensor can be located in hazardous explosive areas up to zone 0
- Relay or transistors output
- High-frequency switching (up to 2kHz – ver. “T”)
- LED state indication
- Power supply 230 V AC or 24 V DC
- Mounting on DIN rail 35 mm
Features of Variants
- NSSU – 811 Single channel unit without additional functions for supply and state detection of one NAMUR sensor. Output invariant “T” (transistor switch) or “R” (relay contact).
- NSSU – 812 Single channel unit with LFD* system for supply and state-detection of one NAMUR sensor. Output invariant “R” (relay contact).
- NDSU – 822 Dual channel unit without additional functions for supply and state detection of two NAMUR sensors. Output invariant “T” (transistor switch) or “R” (relay contact).
- NLCU – 821 2-state level regulation unit using two connected limits NAMUR sensors. Output invariant “R” (relay contact).
- NLCU – 822 2-state level regulation unit with LFD* system using two connected NAMUR sensors, protection against non-logical states of level sensors. Output invariant “R” (relay contact).
Dinel Intrinsically Safe Supply Units Specification
| Model | NSSU–811 | NSSU–812 | NDSU–822 | NLCU–821 | NLCU–822 |
| Number of connectable sensors | 1 | 1 | 2 | 2 | 2 |
| Failure signalization (LFD system) | NO | YES | NO | NO | YES |
| Nominal supply voltage | |||||
| Version 230 V | 30 … 230 V AC/DC (+10%) 50 ÷ 60 Hz | ||||
| Version 24 V | 10 … 30 V AC (+10%) 50 ÷ 60 Hz; 10 … 40 V DC (+10%) | ||||
| Nominal power demand (AC / DC) | 4 VA / 4 W | ||||
| Output open – Circuit voltage | 9.2 V DC | ||||
| Output current – Treshold | 1.55 mA (± 0.1 mA) | ||||
| Current limits for LFD system | – | < 0.1 mA | – | – | < 0.1 mA |
| – | > 6 mA | – | – | > 6 mA | |
| Allowable short-circuit time in input terminals | Unlimited | ||||
| Limit parameters | V; I0 = 10.4 mA; P0 = 27.3 mW; C0 = 1.8 ?F; L0 = 150 mH | ||||
| Safe isolation voltage Um (term. 9 – 16) | 253 V | ||||
| Contact voltage drop (output transistor is closed) | 2 V (Variant “T) | ||||
| Dynamic parameters * (Triggering / Gap pulse) | |||||
| Variant “R” | Min. 50 ms | – | Min. 50 ms | – | – |
| Variant “T” | Min. 250 ?s | – | Min. 250 ?s | – | – |
| Max. switching frequency (Max. load / Without load) | |||||
| Variant “R” | 0.1 Hz / 10 Hz | ||||
| Variant “T” | 2 kHz / 2 kHz | ||||
| Output characteristic (Variant “R”) | |||||
| Version 230 V | 250 V AC / 2 A / 100 VA; 250 V DC / 2 A / 50 W | ||||
| Version 24 V | 40 V AC / 2 A / 80 VA; 40 V DC / 2 A / 80 W | ||||
| Output characteristic (Variant “T”) | 40 V / 50 Ma | – | 40 V / 50 mA | – | |
| Relay contact life (Variant “R”) | Min. 30 x 106 | ||||
| Ambient temperature | -20°C … +60°C | ||||
| Protection | IP20 | ||||
| Housing material | Polylcarbonate | ||||
| Material of terminals | CuBe | ||||
| Max. conductor size | 1 x 2.5 mm2 | ||||
| Isolating voltage (mains terminal/output) | 3500 V | ||||
| Weight Approx. | 0.2 kg | ||||
| * Dynamic parameters are valid by connection to contact on input unit (impulse transmitting from gas-meter, etc.) | |||||
Download Catalog: INTRINSICALLY SAFE SUPPLY UNITS,Dinel-Level and Flow Measurement
Ref: Dinel.cz