Weidmuller ACT20X HART® Transparent RepeaterIndonesia Industrial Parts

Description

The ACT20X-HAI-SAO/2HAI-2SAO HART-protocol transparent current-supply isolators are capable of transmitting 4…20 mA signals from Ex zone 0 into the safe zone. External sensors can be supplied with power through the device. Integrated alarm contacts issue an alert in the event of a malfunction; this makes troubleshooting easier and increases system availability.

The rail mounted current-supply isolators are optionally available in one- or two-channel versions. With 11 mm width per channel, the devices need little space in the electrical cabinet.

Specifications (ACT20X and ACT20X-HAI-SAO-S)

Dimensions and weights

Width : 22.5 mm
Width (inches) : 0.886 inch
Height : 119.2 mm
Height (inches) : 4.693 inch
Depth : 113.6 mm
Depth (inches) : 4.472 inch
Net weight : 186 g

Temperatures

Humidity : 0…95 % (no condensation)
Operating temperature, max. : 60 °C
Operating temperature, min. : -20 °C
Storage temperature, max. : 85 °C
Storage temperature, min. : -20 °C
Operating temperature : -20 °C…60 °C
Storage temperature : -20 °C…85 °C

Probability of failure

MTBF : 177 Years
SFF : 80 %

Environmental Product Compliance

REACH SVHC : Lead 7439-92-1

Rated data UL

UL certificate : E337701.pdf

Input EX

Input current : 4…20mA
Input frequency : 0,5…2,5 kHz @ 3,5…23 mA bi-directional HART® signal
Output signal in case of wire break : < 1 mA
Residual ripple (current loop) : < 7.5 mVeff
Sensor supply : 3.8…26 V DC
Type : intrinsically safe circuit, active (as current source) or passive (as current sink)
Voltage drop not powered : < 6 V
Voltage drop powered : < 4.5 V

Output

Load stability : ? 0.01 % of end value / 100 ?
Type : active (as current source) or passive (as current sink)
Influence of load resistance : ? 0.01% of span / 100 ?
2-wire supply : ? 26 V DC
Output signal limit : < 28 mA
Output current : 4…20 mA
Cut-off frequency (-3 dB) : 0.5…2.5 kHz @ 3.5…23 mA bi-directional HART® signal
Load impedance current : ? 600 ?

Alarm output

Alarm function : Signal limit exceeded, Line interruption at the input, No supply voltage, Device error
Type : Relay, 1 NC (voltage-free)
Nominal switching voltage :
? 125 V AC / 110 V DC (safe area)
? 32 V AC / 32 V DC (zone 2)
Continuous current :
? 0.5 A AC / 0.3 A DC (safe zone)
? 0,5 A AC / 1 A DC (zone 2)
Power rating :
? 62.5 VA / 32 W (safe area)
? 16 VA / 32 W (Zone 2)

General specifications

Configuration : With FDT/DTM software
Voltage supply : 19.2…31.2 V DC
Type of connection : Screw connection
Power consumption : ? 1.0 W
Accuracy : < 0.1% span
Temperature coefficient : < 0.01% of span/°C (TU)
Step response time : ? 5 ms
Protection degree : IP20
Humidity : 0…95 % (no condensation)

Insulation coordination

EMC standards : DIN EN 61326, NE 21
Insulation voltage : 2.6 kV (input / output)
Pollution severity : 2
Rated voltage : 300 V
Surge voltage category : II

Data for Ex applications (ATEX)

Voltage U0 : Current loop 28 V / externally 10 V
Current I0 : Current loop 93 mA / externally 10 mA
Power P0 : Current loop 0.65 W / externally 0.1 W
Marking : II (1) G [Ex ia Ga] IIC/IIB/ IIA, II (1) D [Ex ia Da] IIIC, I (M1) [Ex ia Ma] I
Installation location : Device installed in safe area, zone 2

Safety-related basic specifications

Demand mode : High
Description of the “safe state” : analogue Output ? 3.6 mA or output ? 21 mA
Device type : A
Hardware fault tolerance (HFT) : 0
Mean Time To Repair (MTTR) : 24 h
Safe Failure Fraction (SFF) : 80 %
Tproof : 5 Years
Total failure rate for dangerous detected failures (?DD) : 173 FIT
Total failure rate for dangerous undetected failures (?DU) : 41 FIT
Total failure rate for safe detected failures (?SD) : 0 FIT
Total failure rate for safe undetected failures (?SU) : 0 FIT
Safety category : SIL 2
Probability of outage PFH : 4.1 x 10-8 h-1

Safety-related specifications Low demand mode

Average Probability of Failure on Demand (PFDavg) :
1.92 x 10-4 (Tproof = 1 year), 3.67 x 10-4 (Tproof = 2 years), 8.92 x 10-4 (Tproof = 5 years), additional data in the safety manual