AquaMotion AM5-F1 Cast Iron CirculatorsIndonesia Industrial Parts

Single-speed and 3-Speed, Stainless and Cast Iron

AquaMotion AM5-F1 are revolutionary “Green Eco Cartridge™ Design” is the heart of the circulator and contains all moving parts. It has the only field replaceable and field serviceable cartridge on the market. In case of failure, competitive manufacturers have to replace their entire cartridge, motor assembly or pump, increasing the foot print on the environment and doubling the cost to the consumer. With our pump, pull out the rotor assembly, flush the cartridge with water and reinstall it. Simple, cost effective, patented. Patent No. 8,083,500 and No. US 8.303.184 B1.

The AquaMotion AM5-F1 is a cast iron circulator pump designed for residential and commercial systems such as closed-loop hydronic heating systems, radiant heating, heat recovery systems, and indirect water heating applications. It comes with a wet motor cartridge design allowing, quiet operation and convenient installation. This circulator pump is also designed with a flange and a 2-bolt connection.

This rugged single-speed model has an Ampere draw of 0.54 amps and a maximum flow rate of 18 GPM offering high and efficient performance. It features the Green Eco Cartridge Design, which acts a the heart of the circulator containing all the moving parts, allowing easy, cost-efficient maintenance and service-free performance while preventing black iron oxide and contaminants from entering into the cartridge.

AquaMotion AM5-F1 circulators are designed to handle water and mixtures of water and up to 50% ethylene or propylene glycol. The addition of certain chemical

Specifications of AM5-F1

AquaMotion AM5-F1 Maximum water temperature 1100C/2300F
Maximum working pressure 125 psi
The maximum ambient temperature with 2300F fluid is 1040F
Minimum inlet pressure 2 psi
AquaMotion AM5-F1 Electrical Ratings 120V, 60Hz
*For addition of 10ft line cord with groundedplug, add “L” at the end of each product number*

AquaMotion AM5-F1 Materials of Constructions

Components

STAINLESSSTEEL:Wearring, bearing support, cartridgesleeve, rotor sleeve, rotor cover
STEEL: Motor housing
ALUMINIM OXIDE CERAMIC: Shaft
CARBONIMPREGNATED:Radial bearings
CAST IRON: Pump housing (volute) (Closed Systems)
STAINLESS AND LEAD FREE BRASS: Open systems
EP (Ethylene Propylene Rubber): O-ring and gaskets
POLYPROPYLENE: Impeller

Applications

AquaMotion AM5-F1 circulators are designed to handle water and mixtures of water and up to 50% ethylene or propylene glycol. The addition of certain chemical additives or petroleum based products voids the warranty.
For closed loop systems, circulator with cast iron pump housings may be used.
For open loops and fresh or potable water, use pumps with bronze or stainless steel housings only.
AquaMotion AM5-F1 Operating pressures may not exceed 125psi.
Maximum fluid temperatures must not exceed nameplate rating.
Maximum ambient air temperature is 104?F. (For higher ambient temperatures consult factory).

Installation and Start-Up

AquaMotion AM5-F1 Prior to installation, check circulator for damage due to mishandling.
Mounting position: The circulator may be installed with the motor in the horizontal position or vertically with the motor up. (Do not install with the motor down).
Flow directions: An arrow on the pump housing indicates the direction of flow.
Rotating motor: The motor can be rotated relative to the pump housing so that the junction box is located in the most convenient position. However, it must not be located at 6 o’clock when the motor is horizontal. To rotate the motor, remove the fur housing bolts, rotate and replace bolts. Make sure the 0’ring gasket is properly located in the recess of the pump housing.
AquaMotion AM5-F1 Electrical connections: OBSERVE ALL APPLICABLE CODES WHEN CONNECTING POWER. Check nameplate for voltage and ampere draw. The motor is impedance protected; no additional overload protection is required. The black supply wire may be connected to either motor wire. The pump cannot run backwards. Use supply wires rated not less than 90?C. Use copper conductors only. Attention: Employer des fils d’alimentation pour 90?C. Utilisez des conducteurs en cuivre seulement.
Charging the system: The bearings of the AquaMotion pumps are lubricated by the fluid being pumped, hence they never need to be lubricated. However, to assure adequate initial lubrication, the system must be filled and pressurized. In vertical position, a minimum of 20 psi is required. DO NOT OPERATE THE PUMP UNTIL SYSTEM IS PROPERLY FILLED AND PRESSURIZED
When system has been properly filled, operate the pump for 5 to 10 minutes to further purge air from pump.

Ref : www.aquamotionhvac.com

Download Data Sheet : AquaMotion AM5-F1 Cast Iron Circulators SS

Download Instructions Sheet :AquaMotion AM5-F1 Cast Iron Circulators IS

Other Article: