Flocorp Tracer 1000 LTT1-2G 2nd Generation Radar Level Transmitter provides continuous level measurement in liquids, solids, and slurries. This innovative device has almost no installation restrictions in tanks, silo, and bins up to 80 feet. The Tracer 1000™ 2G has a fully isolated 4-20 mA output that can be scaled for tank level or distance. The unit requires 18 to 30 VDC power.
The 4-wire device comes standard with an RS-485 COMMS output that can be connected to the Tracer Talker™ software for custom configurations and detailed level processing analysis. The Tracer 1000™ 2G ships pre-calibrated precisely for the customer’s application for quick installation and setup. If adjustment is needed in the field the RS485 Communication Tool and Tracer Talker™ software is recommended.
TDR technology is not affected by pressure, vacuum, temperature, viscosity, foam, or dust. Changes in the dielectric constant or coating of the probe do not affect the level measurement due to the dynamic sensing technology programmed into the artificial intelligence of the Tracer 1000™ 2G GWR level transmitter
Flocorp Tracer 1000 LTT1-2G Features and Benefits
- Revolutionary TDR Technology
- Auto Calibration to any dielectric
- Precise continuous level measurement
- Measures liquids, slurries, and solids
- Highly robust measurement due to the 4-wire design and innovative signal analysis and constant disturbance signal suppression
- Measures up to 80 feet
- Pre-calibrated from factory for easy installation
- High-temperature applications
- Programmable fail-safe mode
- RS485 Communication Tool and Software are available for purchase if calibration adjustments are required
Primary Area of Applications
- Chemical / Petrochemicals
- Energy
- Food & Beverages
- Plastic Pellets
- Minerals & Mining
- Oil & Gas
- Pharmaceutical
- Pulp & Paper
- Wastewater
- Transport
- Overflow Protection
- Asphalt Blending Tanks
- Alum and Wax Tanks
- Sand and Gravel
- Primary and Secondary Sludge Clarifiers
- Fresh Cooking Oil
- Used Cooking Oil
Flocorp Tracer 1000 LTT1-2G Specification
| Signal Output | Isolated 4-20 mA (750 ohms @24Vdc |
| User Voltage Supply, 250 ohms internally driven) | |
| Fail-Safe Output | 3.8 mA, 4 mA, Last Known, 20 mA, 20.2 mA |
| Operating Voltage | 12-30 Vdc (residual ripple no greater than 100 mV) |
| Power Consumption | <3W @ 24 Vdc |
| Communications | RS485 Modbus |
| (RS485 activation required Tracer Talker™ Communication Software and Tool). | |
| Signal Wiring | Recommended Signal Output and Communications Output is twisted shielded pairs, 20-18 AWG |
| Measurement Range | 1.2’ to 80’ with minimum dielectric |
| constant of 0.3 | |
| Resolution | 0.0008″ |
| Accuracy | +/- 0.039” ( 1 mm) or 0.02% of the measured distance, whichever is greatest. |
| Update Interval | 100 samples/sec/updated <100 millisec. |
| Ambient Temp. Effect | +/- 0.005”/K of a measured value |
| Repeatability | +/- 0.02” (0.5mm) |
| Electronics: -40º to 158ºF (-40 to 70ºC) Process/Probe: -40º to 398ºF standard | |
| Maximum Operating Temperature | -50º to 593ºF with Temp. Extender Option |
| Maximum Operating Pressure | -14.50 PSI to 580 PSI |
| Process Connection/ Type | Standard: 1.50″ MNPT |
| Option: 1.50″ ANSI 150lb. Flange | |
| Probe Type/Diameter | Rod Probe: 316 Stainless Steel, 0.25″ diameter |
| Wire Cable Probe: 316 Stainless Steel, 0.195″ diameter Weighted Assembly: 0.75″ diameter | |
| Tensile Load | 4,270 lbs |
| Enclosure | NEMA 6: Coated Epoxy Aluminum with IP67 Sealing |
| Cable Entries | (2) 1/2″ NPT Conduit Entries |
| A22 ATEX Grp II Cat 3 GD T75°C IP67 | |
| Approvals | Tamb -40°C to 65°C |
Ref: Flo-corp.com
Download Datasheet: Tracer 1000™ LTT1-2G 2nd Generation Radar Level Transmitter Flocorp
Another Article:
- LEEG Pressure Transmitter, Sensor and Switch
- D22 Pressure Transmitter Delta Mobrey
- 8000 SAN Pressure Transmitter Delta Mobrey
- Hengesbach Pressure Transmitter DME 11 Series
- Pressure Transmitter 8000 Series Delta Mobrey