Kofloc DF-250C Series Digital Mass Flow ControllerIndonesia Industrial Parts

Description

Kofloc DF-250C Series Digital Mass Flow Meters is a high-performance digital mass flow controller with 1 sec response less than 50SLM specification. The series offers a large flow rate line-up up to 300SLM.

Kofloc DF-250C Series Feature

Standard gases are calibrated with actual gas
~50SLM model offers a fast response of ?1 sec
10sccm ~ 300SLM flow range line-up
Communications functions installed as a standard feature(RS485)
RoHS/CE Standard compliant

Specification

Sensor type	Thermal sensor
Valve type	Normally closed proportional solenoid valve
Applicable gases 1	N2, Air, H2, He, Ar, O2, CO2, etc.		Air, N2
	(Gases not specifically mentioned here are subject
	to calibration for N2 equivalent.)
Flow range 2	10 SCCM to 10 SLM	20 to 50 SLM	100, 150 SLM	200, 300 SLM
		(20 to 30 SLM for CO2)
Control range	2 to 100% (F.S.)		5 to 100% (F.S.)
Response 3	Total flow rate control range 1 sec (within ±2% F.S.)		1.5 sec / 3 sec less than 10%	2 sec (within ±2% F.S.)
			(within ±2% F.S.)
Accuracy 4	±1.0% F.S.			±2.0% F.S
Repeatability	±0.25%F.S.			±0.5%F.S.
Operating differential	50 to 300 kPa	100 to 300 kPa	150 to 350 kPa	200 SLM: 200 to 350 kPa
pressure*5	(100 to 300 kPa for Ar and CO2)	(150 to 300 kPa for Ar and CO2)		300 SLM: 250 to 350 kPa
Inlet maximum pressure	500kPaG
Proof pressure	980kPaG
External leak rate	1.0 x 10^-8 Pa·m³/sec (He)		1.0 x 10^-7 Pa·m³/sec (He)
Temperature	5 to 50
	15 to 35
	-10 to 60
Allowable operating humidity	10 to 90% RH (without dew condensation)
Materials of gas contact part	SUS316, SUS316L, magnetic stainless steel, Ni, PTFE, PCTFE, and FKM
Electrical connection	D-sub 9-pin, KFC standard (SEMI standard compliant), RJ-45 modular jacks (two)			D-sub 9-pin ,
				HR-10A (two)
Flow rate setting signal	0 to 5 V DC (input impedance: approx. 1 M)
Flow rate output signal	0 to 5 V DC (load resistance 10 k)
Digital communication	Address setting with RS485 rotary switch: up to 99 devices (9600 bps)
Required power supply (DC)	+15 V DC (±5%): 150 mA		+15 V DC (±5%): 150 mA	24 V DC (±10%): 450 mA
	-15 V DC (±5%): 150 mA		-15 V DC (±5%): 250 mA
Joint 6	1/4 F900 (standard), 1/4 UJR, Rc 1/4		1/2 SW (standard), 3/4 SW
Mounting posture	Horizontal installation recommended.
Weight 7	Approx. 850 g	Approx. 1000 g	Approx. 2250 g	Approx. 3500 g

The gases must be dry and clean, free of corrosive components and foreign matter such as dust and mist.
Dedicated software is available to change gases or change the actual full scale (F.S.) within the range of 30 to 100% (30 to 80% for CO2 only) of the specified full scale.
The flow rate calibration units SCCM and SLM indicate a mass flow rate converted to a volume flow rate in cc/min and L/min at 0°C and 1 atm.
Guarantee for calibration gas: N2.
Accuracy for calibration gas: N2, flow range (max. full scale).
The operating differential pressure may differ depending on specifications.
Contact us for any other joints.
Exclusive of the weight of joint

Other Articles: