Hengesbach NG Turbidity Sensor TURBIMESSIndonesia Industrial Parts

Description

Hengesbach NG Turbidity Sensor TURBIMESS is an optical sensor measuring the reflected radiation arising from particles or fat droplets in liquid media. The operating and display elements are housed inside the device head. In addition to a 4-figure, 7-segment display, the device head features two LEDs and three push buttons.

The device features two switching points. The operating status of each switching point is indicated by an LED. If a switching point is activated, the supply voltage can be measured at the corresponding connection of the M12 plug connector (PNP action). At the same time, the corresponding LED also lights up. If the switching point is not activated, the LED does not light up and there is, therefore, no voltage to be measured at the corresponding switching point’s output.

Hengesbach NG Turbidity Sensor Features

Turbidity sensor with 2-wire 4….20 mA output
Process connections Clamp; Varivent; DIN 11851
2 individual programmable switch-points with status LEDs
Integrated LED display
Easy parametrizing with three push buttons
Compact hygienic design made in stainless steel
2 operating modes:
– NTU mode (linear) for turbidities between 0 and 4.000 NTU
– 9 selectable support points for fat contents up to 30%
Temperature resistant long-term: 125°C /short-term 150°C

Application

detection of product change
(e.g. milk – cream – whey)
continuous monitoring of e.g. milk fat content/quality inspection
monitoring of the cleaning agents’ pollution degree during CIP
detection of filter breakdown
detection of yeast and cloudy fruit juice

Successor

The turbidity sensor TURBIMESS NG replaces the previous turbidity sensor TURBIMESS.

Specification

General details
Device type	TURBINES NG
Measuring principle	Backscatter from the transmitted emitted infra-red light beam
Input
Measuring ranges	Factory setting: Linearised turbidity > 50 to 4000 NTU*
	9 freely configurable reference points
	*Configuration using NTU Standard, measurement procedure approximated
Maximum process pressure	PN16
Output
Output signal	4…20mA, 2-wire
Signal range	3.8…20.5mA as per Namur NE043
Fault signal	22mA
Switched output	2x PNP, each of max. 50mA
	Factory setting: Not activated
Measuring accuracy
Accuracy	± ? 0.2% from measuring range end value
Reproducibility	± ? 0.1% from measuring range end value
Thermal influence	± ? 0.2% / K from measuring range end value
Setting time after input leap	? 3s
Activation time	< 2s (The device will carry out a self-test.)
Conditions of use
Installation position/calibration position	The optimal installation position is in risers (ascending pipes) or, if not possible, to the side of other pipes (to
	avoid product residues and incorrect measurements due to gas bubbles); the device must not be installed in downpipes (descending pipes).
Medium temperature	0…125°C / up to 150°C for brief periods (max. 30 mins)
Ambient/storage temperature	-10…85°C
Protection class acc. to EN60529	IP 67
Electromagnetic compatibility	acc. to DIN EN 61000 and DIN EN 61326-1
Construction
Electrical connection	Round plug-in connector M12x1, 5-pin, nickel-plated brass (stainless steel available on request)
Process connection	Clamp connection acc. to DIN 32676, DN50/2″
Materials	Varivent flange Type F (d50) and Type N (d68)
	Conical couplings with groove union nuts acc. to DIN 11851, DN50 and DN65 ?? Scope of delivery does not incl. seals and, where applicable, clamps
	– Field housing/lid:	Stainless steel 1.4301 (AISI 304)
	– Inspection gauge in the lid:	Polycarbonate (PC)
	– Housing seal:	FPM (Viton®)
	– Process connection/connection adapter:	Stainless steel 1.4404 (AISI 316L)
	– Medium-contacting density gauge:	Sapphire glass
	– Seal on gauge:	Silicone rubber, approved by FDA
Weight	approx. 1.5kg
Display and operation
Display	4-figure, 7-segment display, incl. decimal point, 2x status LED for switching points
Operation	3 input keys
Auxiliary energy resources
Power supply/burden	24…30V DC, max. burden: 600 ?
Accessories
Certificates	EG Declaration of Conformity
	Conformity acc. to Regulation (EC) 1935/2004
	Acceptance test certificate 2.2 in acc. with EN 10204 for parts that come into contact with products